How to Change Time on Armitron Watch

Armitron watches are a popular line of affordable, fashionable timepieces. It is important to know how to change the time on an Armitron watch in order to keep accurate track of your schedule and other activities. Follow these simple steps for changing the time on an Armitron watch:

1. Pull off crown from caseback by twisting it counterclockwise
2. Turn crown clockwise until you feel resistance
3. Push crown back into place until it snaps
4. Adjust hour hand with stem
5. Adjust minute hand with stem
6. Put crown back onto caseback by twisting it clockwise 7-10 times Be sure not to over tighten the crown or else you may break the crystal.

The Armitron watch has a small button on the side of it. Pressing this button will cycle through all of the settings and allow you to change them.

How do I change the time on my Armitron WR165ft watch?

To change the time on your Armitron wr165ft watch, you will need to remove the back of the watch. This can be done by using a small screwdriver and prying it off from one side. Once that is completed, you will find a set of gears inside that are responsible for powering the hands on your watch. You will also see two pins which control where the hands move. These pins have arrows next to them which indicate how far they need to be pushed in order for them to make a full rotation of 360 degrees or 12 hours. You should start by pushing these forward until they reach their furthest point and then pull them outwards so they are at their original position before continuing with what was described.

1. Check to see if your Armitron wr165ft watch is set for the correct time
2. If it's not, you'll need to change the time zone or adjust the date and time manually
3. To do this, use a small screwdriver to remove the back of your watch
4. Once you have taken off the back of your watch, look for two buttons on either side of a battery compartment
5. Use one finger to press down on both buttons at once until they are released
6. You will now be able to make adjustments with an analog clock face that is located at 12 o'clock position on your Armitron wr165ft watch

To change the time on your Armitron wr165ft watch, first pull off the crown. Then turn it to adjust for AM or PM and then move the crown until you reach the correct time zone.

How do you set a 4 button digital watch?

1. First, press the top button on the watch
2. Second, press and hold down the bottom right button
3. Third, use your left hand to set the hour by turning the knob clockwise
4. Fourth, use your right hand to set minutes by turning the knob counterclockwise
5. Press and release both buttons at once when you are done setting time
6. Finally, press and release all four buttons together for a few seconds (to save settings)

How do I set the time on my automatic watch?

1. Find the crown on your watch
2. Turn the crown counter-clockwise to wind it up
3. Push in on the crown and turn clockwise to set time
4. Winding a watch is necessary every day, or else it will stop working altogether!
5. If you have an automatic watch that has stopped working, try winding it by hand until you hear a "click" sound - this means that your movement is being transmitted through the gears again and should start running normally

How do you adjust the moon phase on a watch?

1. The moon phase on a watch is adjusted by rotating the bezel
2. The moon phase can also be adjusted by turning the crown, but this will affect the date and time as well
3. If you don't want to change your watch's date or time, you'll need to set it ahead one day before adjusting the moon phase
4. Don't forget to wind your watch after adjusting its settings!
5. Be sure not to adjust any other settings on your watch while changing its position - doing so could result in an error message or even damage your device
6. When setting up a new battery, make sure that it is inserted with both ends facing down and that there are no spaces between the positive and negative terminals of the battery inside of the compartment

How do you tell if a moon is waxing or waning?

1. When a moon is waxing, it means that the moon is growing in size and will be full at some point
2. A waning moon refers to a time when the moon's size has diminished and it will not be full again for another cycle
3. The most common way to tell if a moon is waxing or waning is by looking at its shape
4. If you can see more than half of the surface of the disc, then you are seeing a waxing crescent
5. A waning gibbous refers to when there are less than two weeks left before the next new moon
6. Another way to tell if an object in space is waxing or waning would be by observing how much light it emits

How do you change the time on an Armitron 330?

1. Remove the watch from your wrist
2. Press the button on the side of the watch for about two seconds
3. The time should change to 12 o'clock, which is what you need if it's currently set to anything else other than midnight
4. Press any button to make sure that it has saved your new time and date settings, or press "C" for constant mode if you want it to stay at this time forever!
5. Put your Armitron back on and enjoy not having an incorrect time anymore!
6. If all goes well, you should be able to tell people around town that you're a pro with watches now!

Conclusion:

First, make sure that the date is set correctly. Then, use the two buttons at 2 and 4 o'clock to scroll through different modes until you see "set", which will be highlighted in blue. Push the button once then adjust it by rotating crown clockwise or counter-clockwise to get closer to 12 AM or 12 PM respectively. When adjusting for daylight savings time, push down on the crown twice.